There is no single best fastening tool. A digital torque wrench, a DC nutrunner, a pulse tool, a clutch screwdriver and an automatic screwfeeding system all have a place on a production line. The right one depends on the joint, the volume and how much evidence you need that every fastener is right.

We supply and service Atlas Copco, Delta Regis, Durofix and Fiam tools, so we see each of them working well, and each of them in the wrong job. These are the five points we look at when helping a customer choose.

1. Torque accuracy and joint control

Start with the tolerance the joint actually needs.

  • Atlas Copco STRwrench (±1%): the most precise option. Digital strain gauges and a residual torque algorithm remove the variation that comes from how fast the operator pulls.
  • Atlas Copco Tensor IxB (±5%): tight accuracy on both hard and soft joints, with torque and angle monitored inside the tool. See the Tensor ITB-P cordless nutrunner.
  • Fiam screwfeeding (±5% to ±10%, depending on the driver): Fiam eTensil DC electric drivers give ±5% with torque and angle control. Air or electric clutch drivers give ±10%.
  • Atlas Copco TBP and Delta Regis (±10%): repeatable control through hydraulic pulsing (the TBP pulse tool) or mechanical shut-off clutches (Delta Regis screwdrivers).
  • Durofix Pro-Assembly impacts and pneumatic tools (±15–20% or more): best for heavy rundown and non-critical fastening.

2. Error-proofing and data traceability

If a customer or auditor will ask you to prove a joint was tightened correctly, this point outweighs the others.

  • STRwrench, Tensor IxB and TBP: full digital traceability, barcode scanning and torque-angle curves logged to your MES.
  • Fiam: each screw is blown straight to the bit tip, which prevents dropped, missed and double-fed screws. Smart controllers check a screw is present, count batches, and flag cross-threads or height errors such as floating screws.
  • Delta Regis and Durofix: basic OK/NOK cycle counting and batch checks when used with external controllers or wireless PLCs.
  • Pneumatic tools: no built-in feedback or traceability unless you add air-line monitoring.

3. Reaction force and operator ergonomics

  • Fiam: removes the repetitive hand-picking of small screws, a major cause of RSI and fatigue. Telescopic nosepieces and lightweight inline drivers allow one-handed work.
  • TBP and Durofix: high torque with almost no kickback, so no reaction bar is needed.
  • Delta Regis and Tensor IxB: lightweight housings and programmable soft starts reduce wrist strain.
  • Pneumatic and STRwrench: air tools add vibration and noise (see our guide to hand arm vibration). The STRwrench needs manual pulling force, so it suits low-volume work and audits.

4. Cycle speed and line flexibility

  • Fiam: the fastest cycle times for high-volume repetitive fastening, typically 30–50% quicker because the next screw is already at the bit. The trade-off is that the station is dedicated to one screw geometry, so it is less flexible. See Fiam automatic handheld screwdrivers.
  • TBP, Durofix and pneumatic: fast free-spin rundown with full freedom of movement.
  • Tensor IxB and Delta Regis: cordless models make rebalancing a line quick. Corded Delta Regis units are ideal for fixed bench stations.
  • STRwrench: the slowest, because it is manual, but hot-swappable smartHEADs cover several torque specs with one wrench.

5. Total cost of ownership and maintenance

  • Fiam: a higher upfront cost (bowl feeder, escapement unit and controls), but a quick return on high-volume lines through no wasted screws and less labour. It needs clean, consistent fasteners to avoid jams.
  • Tensor IxB, TBP and STRwrench: higher capital cost, offset by brushless motors, long calibration intervals and no defect escapes.
  • Delta Regis and Durofix: lower upfront cost, with periodic spring calibration, clutch wear parts or hammer maintenance to budget for.
  • Pneumatic: the cheapest to buy, but generating compressed air and losing it through leaks push up running costs. Our electric vs pneumatic comparison covers this in more detail.

Putting it together

For safety-critical joints that need a record, choose a transducerised tool such as Tensor IxB, TBP or STRwrench. For high volumes of small screws, Fiam screwfeeding pays for itself quickly. For general assembly where a clutch is accurate enough, Delta Regis and Durofix keep costs down. Whatever you choose, regular torque calibration keeps it delivering the torque you specified.

For a broader checklist on air tools, read how to choose the right air tool. Or talk to us about your application and we'll recommend the right tool for the job and quote for it.